Stop counting.
Start winning bids.

Upload your plans. Get a perfect takeoff and a priced estimate in minutes — in your numbers, with your name on it.

14-day free trial · no charge today

Real takeoffs · every trade

Pick your trade. See exactly what comes back.

Actual line items from real plan sets — down to the square foot. Some trades count devices, some measure area — the engine knows which. See all 12 trades →

Electrical takeoff

Real run · custom home, 6 electrical sheets

Count-based Done in ~90s

Recessed can, 6"

LED, from lighting plans

214

$18,832

Duplex receptacle, 15A

From power plans

167

$7,515

GFCI receptacle

Kitchen, bath, exterior

$6,600

Surface-mount fixture

$6,460

Single-pole switch

151

$6,342

Recessed can, 4"

$4,510

Smoke detector

$1,980

Main panel, 200A

$1,850

Estimated total

$65,366

in your prices · your margin applied

✓

Every line

straight off the plans

✓

Counted

not eyeballed

✓

~90 seconds

start to finish

Estimate your first plan free

Actual line items from a real electrical takeoff — exact counts and measurements, done in about 90 seconds.

Built to be right

Why your number comes back accurate.

12 trades

One estimating engine — electrical to concrete, every division of the job.

Every device

Counted straight off the plans, sheet by sheet — nothing eyeballed.

Every wall

Measured to the square foot from the drawings, not a rough guess.

Your prices

Priced in your own catalog and margin — never generic rates.

Three steps. No new software to learn.

You already know how to read a plan and price a job. This just does the tedious middle part.

Drop the PDF

Architectural, electrical, lighting, power, low-voltage — a single sheet or a 40-page set.

It reads every sheet

Counts devices and fixtures, measures walls, ceilings, floors and exterior — using the legend on each page.

You get a priced estimate

Quantities meet your catalog. Edit lines, set markup, see your margin, send a branded proposal.

Built for your trade

One engine. Every trade on the job.

Count-based trades tally devices; area trades measure square footage. Open your trade to see how it works and a real sample.

ElectricalCount

receptacles, GFCIs, weatherproof and quad boxes…See electrical estimating

PlumbingCount

toilets, lavatories, kitchen sinks…See plumbing estimating

PaintingSF

interior wall paint (net of openings), exterior wall paint, ceilings…See painting estimating

FramingSF

exterior (2x6) and interior (2x4) wall framing by linear foot, floor joists and rim, roof trusses and rafters…See framing estimating

FlooringSF

luxury vinyl plank, tile (with thinset and grout), carpet and pad…See flooring estimating

HVACCount

condensing units, air handlers and furnaces, supply registers…See hvac estimating

RoofingSF

architectural shingles with underlayment by the square foot (pitch-adjusted), ridge cap, valley flashing…See roofing estimating

Siding / ExteriorSF

fiber-cement or lap siding with house wrap by the square foot, vented soffit, pre-finished fascia…See siding / exterior estimating

Windows & DoorsCount

windows by type from the schedule, exterior doors and sliders, interior pre-hung doors…See windows & doors estimating

InsulationSF

wall batts (R-21), attic blown-in (R-49), floor batts (R-30) by the square foot per assembly…See insulation estimating

DrywallSF

wall board (1/2") and ceiling board (5/8") by the square foot, moisture-resistant board at baths and laundry, and corner bead with Level 4 tape and finish…See drywall estimating

ConcreteSF

foundation slab with vapor barrier and mesh by the square foot, continuous footings by the linear foot, driveway and walk flatwork…See concrete estimating

General Contractors

Bid the whole set across every division — or hand each trade to your subs.Whole-set estimating for GCs

Marketplace

Or skip the takeoff and just get bids.

Homeowners & GCs — post your project free and hear back from local, subscribed contractors. And every EstimateBy subscriber sees local jobs in their trade to bid on. Leads, built in.

Post a project — free Contractors: get local leads

Refer & save

Invite your subs. You both save $50.

Need trades on a job — drywall, plumbing, roofing? Invite them from any project. When they subscribe, you each get $50 off — $100 saved between you. Get your whole crew on it and every takeoff gets cheaper.

Start free & invite your crew

$50

You

$50

Your sub

$100

saved

Priced like a tool, not a tax.

Annual billing saves ~2 months · invite a sub and you both save $50 · homeowners post projects free.

Starter

Solo tradesman, one trade.

$59.00/mo

or $590.00/yr

Choose Starter

Your trade
20 takeoff credits / mo
Then $5 / credit
Bid local jobs in your trade
Branded proposal PDFs

Stop counting.Start winning bids.